manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 229 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 229

7 - MAINTENANCE

Drive belt

WARNING

Entanglement hazard!
Always stop the engine and engage the parking brake, unless otherwise instructed in this manual,
before checking and/or adjusting any drive belt or chain.
Failure to comply could result in death or serious injury.

W0097A

WARNING

Moving parts!
Install all covers, panels, and guards after servicing or cleaning the machine. Never operate the ma-
chine with covers, panels, or guards removed.
Failure to comply could result in death or serious injury.

W0135A

Replace the drive belt when the hour meter registers 1500 hours. Check the belt visually each day at the daily walk
around for correct tension, wear, and damage. Wrong belt tension may cause battery charge failure, engine over-
heating, or drive belt wear.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance.

Maintenance Specifications

Visual check

Every 10 hours or every day

Replace belts

Every 1500 hours

NOTICE:

If the engine runs with the drive belt loose, the drive belt can slip and cause the engine to overheat or the

battery to receive insufficient charge.

Replacing the drive belt

1. Turn the master disconnect OFF.

2. Locate the drive belt.

RAIL12DOZ034AA

1

7-73

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments