manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 42 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 42

2 - SAFETY INFORMATION

Deceleration or transmission pedal informa-
tion

RAIL12DOZ1254AA

18

This informational sign is located above the
deceleration or transmission pedal inside the operator’s
compartment.
The deceleration pedal reduces the engine RPM. The
transmission pedal de-strokes the hydraulics. Depress
the pedal to slow the machine. Release the pedal to
increase the machine speed. Failure to comply with this
warning could result in death or serious injury. (This is a
dual function pedal-deceleration or transmission).
Informational sign number: 47449566

RAIL12DOZ1253AA

19

WARNING — Rollover Protection Structure (ROPS)

RAPH12DOZ0121AA

20

This WARNING safety sign is located inside the left rear
access compartment.
WARNING — Do not modify or repair ROPS or FOPS in
any manner. Failure to comply with this warning could
result in death or serious injury.
English safety sign number: 383972A1
French safety sign number: 87715063
Spanish safety sign number: 87715063

383972A1

21

2-20

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments