manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 155 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 155

6 - WORKING OPERATIONS

Engine starting aids

Starting the engine

WARNING

Explosion hazard!
DO NOT use ether starting fluid. Serious engine damage, explosion, death, or serious personal injury
could occur.
Failure to comply could result in death or serious injury.

W0148A

1. Make all seat adjustments before starting the engine. Fasten the seat belt.

2. Turn the key switch to ON, and watch the instrument cluster. The engine preheat lamp will illuminate If the tem-

perature is low and engine preheating is required. Wait until the preheat lamp goes out before starting the engine.

3. Place the hand throttle at the 1/2 throttle position and hold until the engine starts.

4. Actuate the starter motor.

Additional starting aids may be available on your machine. For additional information on these items, contact your
authorized dealer.

Engine coolant heater (if equipped)

The right side of the engine cylinder block is provided with
a passage for installing a coolant heater. See your autho-
rized dealer for this option. Follow the heater manufac-
turer’s instructions for installation and operation.

RAIL14DOZ0566AA

1

6-19

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments