manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 120 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 120

4 - OPERATING INSTRUCTIONS

Auto park brake setting

To adjust the auto park brake setting, follow the same
steps as for steering sensitivity, then highlight “AutoPrk-
Brk”.

The AutoPrkBrk choices are:

• On (default)

• Off

After you select and highlight the desired value, press the
enter switch (down on the enter/escape switch) to confirm
the selection. Press the escape switch (up on the enter/
escape switch) to store the choice.

The park brake will engage when:

• The AutoPrkBrk function is set to “ON”

• The machine is in neutral and

• The UCM senses movement from the drive motor

speed sensors for

30 s

.

Factory Set

This setting allows the reset of functions to factory default.
Follow the prompts, and press the enter switch to confirm
the selection.

RAIL12DOZ0217AA

5

4-18

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments