Case 2050M Operator'S Manual Download Page 44 | Manualshive

Page: 44 / 286

Case 2050M Operator'S Manual Download Page 44

2 - SAFETY INFORMATION

WARNING — Pressurized fluid hazard

RAIL13DOZ1693AA

26

This WARNING safety sign is located in the front access
compartment on the engine valve cover.
WARNING — Do not open high pressure fuel system
with engine running. Engine operation causes high fuel
pressure. High pressure fuel spray can cause serious
injury or death. Failure to comply with this warning
could result in death or serious injury.
English safety sign number: 84242780
French safety sign number: 87715063
Spanish safety sign number: 87715063

84242780

27

WARNING — Entanglement hazard

RAIL12DOZ1025AA

28

This WARNING safety sign is located behind the grille
cover on the front of the machine.
WARNING — Entanglement hazard. Keep clear or stop
engine before servicing. Failure to comply with this
warning could result in death or serious injury.
English safety sign number: 332512A1
French safety sign number: 332511A1
Spanish safety sign number: 332511A1

332512A1

29

2-22

«
...
42
43
44
45
46
...
»

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments