Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 237

Page: 237 / 242

4 / 8

NOTE:

If the rollers of the ITB Unit (see the figure below) are soiled, follow the cleaning procedure shown below to

clean the whole circumferences of the rollers.

[The roller to be cleaned with a vacuum cleaner and dry lint-free paper]

- 1 Primary Transfer Roller [1]

[The rollers to be cleaned with dry lint-free paper]

- 1 Secondary Transfer Inner Roller [2]

- 1 ITB Drive Roller [3]

[The rollers to be cleaned with a vacuum cleaner and lint-free paper moistened with alcohol]

- 1 Steering Roller [4]

- 4 ITB Slave Rollers [5]

CAUTION:

- Rotate the rollers in the direction of the arrow shown in the figure below, and clean them in the vertical

direction.

- When cleaning the Primary Transfer Roller, make sure to remove the ITB static eliminator from the edge of

primary transfer roller unit.

- After cleaning, remove the paper you placed, and discard the toner according to the specified method.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands