Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 143

Page: 143 / 242

5 / 8

MEMO :

When the ITB is removed, if the back side of ITB is dirty, make sure to clean it in the following procedure.

1) Place the removed ITB on the paper.

2) Clean the back side of ITB by evenly wiping all circumference in vertical direction with the lint-free paper

moistened with alcohol.

14) After cleaning, remove the paper you placed, and discard the toner according to the specified method.

15) Install the removed parts in reverse order.

CAUTION:

Make sure to avoid the edge of the ITB displacement sensor lever from overlapping with the ITB at

installation.

16) ITB position shall be adjusted with a service mode whenever ITB pressure is released.

(ITB positioning adjustment : COPIER > FUNCTION > INSTALL > INIT-ITB)

CAUTION:

If the image failure persists after performing the foregoing cleaning, perform the procedure shown below to replace

the parts.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands