Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 148

Page: 148 / 242

2 / 5

4) While rotating the Secondary Transfer External Roller [1], clean the whole circumference in the vertical

direction with dry lint-free paper.

5) Install the removed parts in reverse order.

CAUTION:

If the image failure persists after performing the foregoing cleaning, perform the procedure shown below to replace

the parts.

1) Open the Front Left Cover and the Front Right Cover

Replacement Procedure

2) Pull Out Fixing Feed Unit

3) Remove the Secondary Transfer Outer Unit.

4) Remove the 2 screws.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands