Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 17

Page: 17 / 242

< Work procedure 1-2>

4 / 19

1) Open the Front Left Cover and the Front Right Cover

Check the Pressure Spring of the Secondary Transfer Roller for any abnormality. [D]

2) Pull Out Fixing Feed Unit

3) Remove the Secondary Transfer Outer Unit.

4) Remove the 2 screws.

5) Lift the post-secondary transfer guide and put it down on front.

Caution

：

Since the harness is connected to the post-secondary transfer guide, be careful not to pull it forcibly.

6) Remove the 2 stop rings.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands