Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 236

Page: 236 / 242

3 / 8

8) Open the intermediate transfer belt unit by approx. 90 degree, align the end of support shaft without

groove with the hole of intermediate transfer belt unit frame and align the other end of groove on support

shaft with the hole of intermediate transfer belt unit frame.

9) Close the intermediate transfer belt unit and hook it to the support shaft to stand it.

10) Remove the patch sensor unit.

11) Put a paper between the fixing feed unit and the ITB frame.

12) Remove the ITB.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands