Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 132

Page: 132 / 242

25 / 31

[B-7] Replacing the Feed Rollers in the Delivery Buffer Unit (Front)

NOTE:

This unit contains 6 Feed Rollers to be replaced. The location is shown in the figure below.

[1-1] Straight Delivery Roller 1, Straight Delivery Roller 2, Duplex Vertical Path Roller 1

[1-2] Duplex Feed Roller 1, Duplex Vertical Path Roller 2, Duplex Vertical Path Roller 3

The following procedures show how to remove the main units to be removed before removing the Feed

Rollers in this unit. If necessary, remove this unit and check the Feed Rollers for any abnormality.

[When replacing Straight Delivery Roller 1, Straight Delivery Roller 2, Duplex Vertical Path Roller 1]

1) Open the Front Left Cover.

2) Pull out the Buffer Delivery Unit.

3) Remove the Delivery Decurler Belt Unit 2.

4) Remove the Buffer Delivery Upper Unit.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands