Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 225

Page: 225 / 242

5 / 13

9) Remove the Drum Drive Unit.

-11 Screws (black TP)

CAUTION:

When removing the Drum Drive Unit, be sure not to damage (bend) the High Voltage Cable since it can be

easily disconnected.

Be sure to free the High Voltage Cable from the Edge Saddle after pulling out the Drum Drive Unit a little.

10) Lift the Drum Shaft Unit, and remove it from the host machine.

- 3 Screws

CAUTION:

When installing the Drum Shaft Unit and the Drum Drive Unit to the host machine, do not remove the 4

screws [1] securing the Process Unit on the front side of the machine.

FRONT

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands