Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 29

Page: 29 / 242

< Work procedure 1-2>

16 / 19

Procedure for Removing the Laser Scanner Unit

Caution:

During the laser scanner unit replacement, do not turn the adjustment dial.

1) Be sure to check that the Laser Scanner is installed correctly (whether there is any backlash).

CAUTION:

- If the Laser Scanner is installed correctly: Install the removed parts in reverse order.

- If the Laser Scanner is not installed correctly: Perform the following steps and check the unit again.

2) Remove the laser fan cover.

- 2 screws

3) Release the flat cable lock then remove 1 cable and 2 connectors.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands