manualshive.com logo in svg

Canon imagePRESS 1135 Series, Troubleshooting Manual

The Canon imagePRESS 1135 Series Troubleshooting Manual is your go-to guide for resolving any technical issues with this exceptional product. This comprehensive manual is easily accessible on our website, where you can effortlessly download it for free, ensuring a smooth printing experience.

Share
Download
background image

Flow of Remedy for Each Type of Image Failure in iPR1135 series

■

Banding Image & Soiling Image ( Appears in interval )

Location

Assumed cause

Work procedure

Approx. 50.3mm

Primary Transfer
Roller

Soiling/damage on the Primary Transfer
Roller

Refer to Work procedure 2-1

Approx. 62.8mm

Feed Roller

Soiling/damage on the Feed Roller

Refer to Work procedure 2-2

Approx. 62.8mm

Secondary Transfer
Inner Roller

Soiling/abnormal wear on the Secondary
Transfer Inner Roller

Refer to Work procedure 2-3

Approx. 76.3mm

Secondary Transfer
Outer Roller

The end of life of the Secondary Transfer
Outer Roller

Refer to Work procedure 2-4

Approx. 84.3mm

Developing Upper
Cylinder

The distance between the Photosensitive
Drum and the Developing Upper Cylinder is
out of the specified range.

Refer to Work procedure 2-5

Approx. 102.4mm

Steering Roller

Soiling/wear on the Steering Roller

Refer to Work procedure 2-6

Approx. 188.5mm

Pressure Roller

The end of life of the Pressure Roller

Refer to Work procedure 2-7

Approx. 113.1mm

External Heat Roller

The end of life of the External Heat Roller

Refer to Work procedure 2-8

Approx. 120.1mm

Developing Lower
Cylinder

The distance between the Photosensitive
Drum and the Developing Lower Cylinder is
out of the specified range.

Refer to Work procedure 2-9

Approx. 125.0mm

ITB Drive Roller

Soiling/damage on the ITB Drive Roller

Refer to Work procedure 2-10

Approx. 251.3mm

Fixing Roller

The end of life of the Fixing Roller

Refer to Work procedure 2-11

Approx. 340.7mm

Photosensitive Drum Uneven rotation of the Photosensitive Drum

Refer to Work procedure 2-12

Remarks:
If the image failure persists after performing the foregoing remedy, check the parts shown
below. If the part is damaged or deformed, replace it with a new one.

_ If the ITB [N] is damaged or bent, replace it with a new one.
_ If the Photosensitive Drum Cleaning Magnet Roller [O] is damaged, replace the
Photosensitive Drum Cleaning Unit.
_ If the ITB Cleaning Magnet Roller [P] is damaged, replace the ITB Cleaning Unit.

Refer to Work procedure 2-13

Where on the paper does the image failure occur?

(Distance appears in interval ?)

Position of the 
poor image

Summary of Contents for imagePRESS 1135 Series



















































































































































































































































Reviews:

No comments

Related manuals for imagePRESS 1135 Series

Canon Pixma MG2400 Series Manual preview
Pixma MG2400 Series
Brand: Canon Pages: 2
NCR 7150 Quick Start Manual preview
7150
Brand: NCR Pages: 2
Canon MP280 Getting Started Manual preview
MP280
Brand: Canon Pages: 31
Pantum P3060 SERIES Manual preview
P3060 SERIES
Brand: Pantum Pages: 115
Xerox DocuPrint 4850 NPS Configuration Manual preview
DocuPrint 4850 NPS
Brand: Xerox Pages: 276
Oki ML590 Specification Sheet preview
ML590
Brand: Oki Pages: 2
Felix printers FELIX Pro L Quick Start Manual preview
FELIX Pro L
Brand: Felix printers Pages: 26
Konica Minolta bizhub C452 Series Replacement Instructions Manual preview
bizhub C452 Series
Brand: Konica Minolta Pages: 17
MUTOH VJ-2638 Operation Manual preview
VJ-2638
Brand: MUTOH Pages: 334
Tally t2145 Operator'S Manual preview
t2145
Brand: Tally Pages: 106
Sindoh 5X Series User Manual preview
5X Series
Brand: Sindoh Pages: 33
Oki B700 Series Installation Instructions preview
B700 Series
Brand: Oki Pages: 4
Ricoh AP204 Operator'S Manual preview
AP204
Brand: Ricoh Pages: 301
Konica Minolta bizhub 215 Installation Manual preview
bizhub 215
Brand: Konica Minolta Pages: 8
Savin 4035e Copy Reference Manual preview
4035e
Brand: Savin Pages: 132
Ricoh Schmidt 3 Installation Manual preview
Schmidt 3
Brand: Ricoh Pages: 8
Lexmark C500N Service Manual preview
C500N
Brand: Lexmark Pages: 60
Xerox VersaLink B625 User Manual preview
VersaLink B625
Brand: Xerox Pages: 342

Brands by name

Popular brands

Load more brands