Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 115

Page: 115 / 242

8 / 31

8) Open the Front Left Cover and the Front Right Cover.

9) Bring down the Fixing Feed Unit Lever to pull out the Fixing Feed Unit.

10) Remove the (Upper) Registration Cover, the (Middle) Registration Cover and the (Lower) Registration

Cover in the direction of the arrow.

- 6 screws

11) Remove the Knob Support Plates (Upper Right), (Middle Left), (Middle Right), (Lower Middle), (Lower

Right) and the Lever.

- 11 screws

12) Remove the Gear Boxes (1) and (2).

- 5 screws

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands