Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 42

Page: 42 / 242

< Work procedure 1-4>

3 / 12

1) Open the Front Left Cover and the Front Right Cover.

Check the Pressure Spring of the Primary Transfer Roller for any abnormality. [C]

2) Remove Process Unit Cover.

3) Pull Out ITB Unit.

CAUTION:

Be sure to pull out the Fixing Feed Unit and ITB Unit to the position where latch is locked.

Reason: Disengagement between the Positioning Pin of the Secondary Transfer Outer Unit and Shaft

Support Member of the frame body of the ITB Unit becomes insufficient, and it may cause damage when

assembling the Intermediate Transfer Belt Unit.

4) Remove ITB Cleaning Unit.

5) Remove the connector.

6) Hold the grip and with opening the intermediate transfer belt unit, remove the support shaft.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands