Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 23

Page: 23 / 242

< Work procedure 1-2>

10 / 19

Check the location to install the Laser Scanner Unit for any abnormality. [F]

NOTE:

Since the preparation for removing the Laser Scanner Unit differs between the ADF + Reader mounted

model and ADF + Reader Unit unmounted model, refer to the preparation which corresponds to each model.

Preparation for removing the Laser Scanner Unit (ADF + Reader Unit unmounted model)

1) Open the Front Left Cover and Front Right Cover.

2) Remove the upper front cover.

- 1 rubber bush

- 3 screws (loosen)

3) Remove the upper cover.

- 6 screws

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands