Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 108

Page: 108 / 242

1 / 31

<Remedy>

Cleaning the Feed Rollers

Roller layout drawing

Unit name

Quantity

Outline of work before cleaning the roller(s)

[B-1] Registration Unit

Remove the Registration Unit.

[B-2] Pickup Feed Unit

Open the Feed Guide.

[B-3] Pickup Unit

Remove the Pickup Unit.

Remove the roller.

[B-4] Duplexing Feed Unit

Open the Feed Guide.

[B-5] Reverse Unit

Open the Feed Guide.

[B-6] Delivery Inner Cover Unit

Open the Feed Guide.

[B-7] Delivery Buffer Unit (Front)

Open the Feed Guide.

Remove the Delivery Inner Cover Unit if

necessary.

[B-8] Outer Delivery Unit

Remove the Outer Delivery Unit.

Cleaning method

CAUTION:

Wipe the rollers with dry lint-free paper. If it is still dirty after wiping it with dry lint-free paper, clean it with

lint-free paper moistened with alcohol.

- If the image failure persists after performing the foregoing cleaning, perform the procedure shown below to

replace the parts.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands