Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 146

Page: 146 / 242

8 / 8

13) Remove the secondary transfer inner roller.

14) Apply Super Lube (FY9-6005-000) about half the size of a rice grain (approx. 20 mg) to at least the half of

the circumference of a new Secondary Transfer Inner Roller at the two places [A] that are fitted in the

bearings.

15) Install the new Secondary Transfer Inner Roller in reverse order.

16) Install the removed parts in reverse order.

CAUTION:

Make sure to avoid the edge of the ITB displacement sensor lever from overlapping with the ITB at

installation.

17) ITB position shall be adjusted with a service mode whenever ITB pressure is released.

(ITB positioning adjustment : COPIER > FUNCTION > INSTALL > INIT-ITB)

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands