Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 153

Page: 153 / 242

2 / 16

Checking for Any Foreign Matters on the Developing Cylinder Drive Gear and the Developing Upper

Cylinder or Replacing the Developing Sleeve Unit

6) Place the paper on the photosensitive drum.

CAUTION:

Be careful not to expose the photosensitive drum to the light.

7) Clean with lint-free paper moistened with alcohol and then apply grease (Super Lube Grease: FY9-6006

is recommended) to the Positioning Blocks (Upper and Lower) at front and rear sides of the Process Unit.

CAUTION:

Uniformly apply 1 rice-grain sized grease with your finger to the same area as the surface to be cleaned.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands