Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 7

Page: 7 / 242

< Work procedure 1-1>

1 / 7

<Remedy>

_Check that the Engagement/Disengagement Cam of the Registration Slave Roller rotates

smoothly. (A loosened screw, a misaligned cam, etc.) [A],

_Check that the bearing at the Engagement/Disengagement Arm of the Registration Slave Roller

is rotating smoothly. [B],

_Check that the Drive Belt of the Registration Drive Roller rotates smoothly. [C],

_Check the connectors between the Registration Motor (M26) and the Registration/Duplexing

Driver PCB. [D]

<Detailed work procedure>

1) Open the Front Left Cover and the Front Right Cover.

2) Pull out the Fixing Feed Unit.

3) Open the duplex feed unit.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands