Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 50

Page: 50 / 242

< Work procedure 1-4>

11 / 12

4) Check the 2 Shaft Support Members [1] of the Fixing Assembly and the 2 pins [2] of the Positioning Plate

on the host machine side for any abnormality.

5) If abnormality is found, replace the faulty part.

6) Remove the knob.

7) While moving the lever lock at the rear of the fixing feed unit toward front and turn the fixing feed unit

lever in the direction of the arrow (clockwise).

MEMO

：

When putting back the fixing feed unit lever, turn the lever lock clockwise while moving it toward front.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands