Canon imagePRESS 1135 Series Troubleshooting Manual Download Page 228

Page: 228 / 242

8 / 13

16) Install the Drum Drive Unit [1].

・

11 Screws [2]

Points to Note when Installing the Drum Drive Unit:

- Install the unit with the boss [1] at the center of the boss hole [2].

- Tighten the 11 screws in the order from 1 to 11 shown in the figure below.

- Be sure that the Static Eliminator [3] is in contact with only the upper side of the Drum Shaft. (The Static

Eliminator should not be on the lower side of the Drum Shaft.)

CAUTION:

Points to Note after Installing the Drum Drive Unit

- Wipe grease off the Static Eliminator with lint-free paper moistened with alcohol.

Grease can be easily removed by rotating the shaft clockwise with the lint-free paper gently pressed against

the Static Eliminator as shown in the figure below.

Summary of Contents for imagePRESS 1135 Series


















































































































































































































































Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands

Canon imagePRESS 1135 Series, Troubleshooting Manual

Search results

Summary of Contents for imagePRESS 1135 Series

Reviews:

Related manuals for imagePRESS 1135 Series

Brands by name

Popular brands