BYD ATTO 3 2022 Owner'S Manual Download Page 64

Page: 64 / 201

CONTROLLER OPER

ATIONS

When the ignition switch is on OK, the

audio control switch is available.
Buttons on the left

Buttons on the left
ACC switch*

• Press this button to enable or disable

the ACC system.

REMINDER

•For instructions on how to use cruise

control, see

"ACC System Setup*"

+/Reset*

• Press this button to activate the ACC

system, and use the previous system

settings.

-/Setup*

• Press this button to configure the current

vehicle speed as the target speed for

cruise control.

Distance-*

• Press this button to reduce the distance

by one notch when the ACC function

is enabled. A total of four notches are

available.

• Press this button to increase the distance

by one notch when the ACC function

is enabled. A total of four notches are

available.

Cancel

• Press this button to change the ACC

mode from active to standby.

ICC

• Press this button to enable or disable

the ICC function.

Screen mode

• Press this button to switch between

the landscape and portrait mode of the

infotainment system touchscreen.

Panoramic view*

• Press this button to enable/disable

panoramic mode.

Buttons on the right

Buttons on the right
Roller
1. Infotainment system

• Turn the roller upward to increase

volume.

• Turn the roller downward to decrease

volume.

• Press the roller to mute.

2. Instrument cluster

• Turn the roller upward to select the

upper level-2 or level-3 menu items in

the instrument cluster menu mode.

• Turn the roller downward to select the

lower level-2 or level-3 menu items in

the instrument cluster menu mode.

• Press the roller:

•

To enter the next-level menu or

confirm the current setting in the

instrument cluster menu mode.

Left/Right button
1. Infotainment system

• In radio mode:

•

Press and hold the

button to

automatically search for the previous

radio station with a strong signal

(turning frequency down).

•

Press the

button to select the

pre-saved radio station upward.

•

Press and hold the

button to

automatically search for the next

radio station with a strong signal

(turning frequency down).

•

Press the

button to select the

pre-saved radio station downward.

Summary of Contents for ATTO 3 2022










































































































































































































Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands

BYD ATTO 3 2022, Owner'S Manual

Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands