BYD ATTO 3 2022 Owner'S Manual Download Page 45

Page: 45 / 201

Description of Other Instrument Faults

The instrument cluster may display the following error messages. Handle them according to

the recommended handling methods.

Symbol

Error Message

Handling

Please check the on-board

charging system.

The on-board charging system is faulty. In

this case, check the charging connection,

and reconnect the charging equipment. If

the fault persists, contact a BYD authorized

dealer or service provider.

Please check the data

network of the vehicle.

The vehicle may be disconnected from the

data network. In this case, park the vehicle

immediately, and contact a BYD authorized

dealer or service provider.

Please check the headlight.

The headlight is faulty. In this case, contact a

BYD authorized dealer or service provider.

Please check the PCW

system.*

The PCW system is faulty. In this case, park

the vehicle, and contact a BYD authorized

dealer or service provider.

The AEB function is limited.*

The AEB system is faulty. In this case, park

the vehicle, and contact a BYD authorized

dealer or service provider.

Please check the BSD system.*

The BSD is faulty. In this case, park the

vehicle, and contact a BYD authorized dealer

or service provider.

The BSD function is limited.*

The BSD function is limited. In this case, park

the vehicle, and contact a BYD authorized

dealer or service provider.

Please check the shifter.

The shifter controller is faulty. In this case,

park the vehicle immediately, and contact a

BYD authorized dealer or service provider.

Summary of Contents for ATTO 3 2022










































































































































































































Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands

BYD ATTO 3 2022, Owner'S Manual

Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands