BYD ATTO 3 2022 Owner'S Manual Download Page 42

Page: 42 / 201

DASHBO

ARD

Drive power limit warning light

When the power of the vehicle is limited,

this warning light goes on. In this case,

contact a BYD authorized dealer or service

provider in time.

Headlight warning light

• If this warning light turns yellow, it

indicates that the headlight is faulty. In this

case, take the vehicle to a BYD authorized

dealer or service provider for inspection.

Main alarm indicator

• If this indicator goes on, check the fault

prompt or warning information in the

information display area.

Unfastened seat belt warning light

• When the ignition switch is on OK, if any

seat belt on the front row is not fastened,

the corresponding seat belt indicator

will be on. The indicator does not go off

unless the seat belt is fastened.

Airbag warning light

• When the ignition switch is on OK, this

warning light goes on. It goes off in a

few seconds if the airbag system works

normally. This warning light is used to

monitor the ECU, crash sensor, inflator,

warning light, wiring, and power supply

of airbags.

• If any of the following cases occurs, a

component monitored by the warning

light system may be faulty. In this case,

contact a BYD authorized dealer or

service provider for inspection as soon

as possible.

• When the ignition switch is on OK,

this warning light does not go on, or is

steady on.

• This warning light goes on while

driving.

Parking brake system warning light

When the brake fluid level is low or the

brake system is faulty, this warning light

goes on. If any of these cases occurs, stop

immediately and contact a BYD authorized

dealer or service provider.

• When the ignition switch is on OK and

the brake fluid level is low, this warning

light goes on.

REMINDER

•When the brake fluid level is low, park

the vehicle because it is dangerous to

continue driving.

• After starting the vehicle, if the brake

fluid level is normal and the EPB is

working normally (the EPB switch can

be pulled up and released normally,

and the prompt "Please check the EPB"

is not displayed), the warning light is

steady on.

• Both the parking brake system warning

light and ABS warning light go on.

Summary of Contents for ATTO 3 2022










































































































































































































Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands

BYD ATTO 3 2022, Owner'S Manual

Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands