BYD ATTO 3 2022 Owner'S Manual Download Page 104

Page: 104 / 201

103

USING AND DRIVING

• Before shifting into "D", ensure that the

power switch is on "OK".

• Press the pedal or the unlock button

when shifting to P or D gear. For

details, see the prompt message on the

dashboard.

• The lever returns to it middle position

after it is released.

WARNING

•

Transmission may be seriously

damaged due to lack of lubrication if

the vehicle is allowed to move for too

long after the motor is turned off and

"N" gear is engaged.

•

When the motor is running and

"R"/"D" gear is engaged, be sure

to keep the brake pedal pressed,

otherwise the vehicle will move.

•

If the gear position is shifted while

driving forward, do not step on the

accelerator pedal.

•

While the vehicle is in motion, do

not push the gearshift lever into "R"

position or press the "P" button.

•

It is not recommended to drive down

slopes in "N" or "P" gear, even if the

motor is not running.

•

To prevent the vehicle from

inadvertently moving, engage the

parking brake and press the "P"

button after the vehicle has stopped.

Electric Parking Brake

(EPB)

EPB Switch

• Ensure the EPB is engaged when parking

and leaving the vehicle.

Manually Engage EPB

• Pull up the EPB switch, and the EPB will

apply an appropriate parking force. The

indicator on the instrument cluster

flashes and then is steady on, indicating

that EPB is engaged. In addition, a text

prompt "EPB activated" is displayed.

CAUTION

• When the indicator flashes, EPB is

working. If the vehicle is on a slope,

do not release the brake pedal unless

is steady on, otherwise the vehicle

may move down.

Automatic EPB Engagement

EPB automatic engagement

• When the vehicle is turned off, EPB

will automatically engage and the " "

indicator will light up on the cluster.

"P" gear automatic engagement

• EPB will engage automatically when the

vehicle stops and "P" gear is engaged.

Do not release the brake pedal until the

indicator on the cluster stops flashing

and the “EPB engaged” message is

displayed.

Summary of Contents for ATTO 3 2022










































































































































































































Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands

BYD ATTO 3 2022, Owner'S Manual

Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands