background image

65

CONTROLLER OPER

ATIONS

04

Steering Wheel Manual 

Adjustment

To adjust steering wheel angle:

 

• Press the steering wheel adjustment 

handle, move the steering wheel to the 

desired angle, or adjust it to the desired 

axial position, and restore the handle to 

the locked position.

WARNING

 

Never adjust the steering wheel while 

driving, under risk of impaired vehicle 

control.

 

After adjusting the steering wheel, 

make sure it is securely locked.

Power-Assisted Steering Mode 

Settings

 

• Steering feel and requirements vary from 

person to person.

 

• Tap on   → Vehicle Settings → Driving 

Comfort Adjustment on the center 

console touchscreen to go to the 

Steering Assist screen, and select the 

Comfort or Sport mode.

REMINDER

 

•If steering feels light when driving at 

high speeds, set the power-assisted 

steering mode to the Sport mode.

Switches

Light Switches

Rotate the rotary knob to 

 to turn off 

all lights except DRLs.

Auto light

Auto light

When the rotary knob is rotated to 

BCM collects the luminance value from the 

light intensity sensor to automatically turn 

on or off small lights and low beam.

CAUTION

 

•The light intensity sensor is located 

at the top of the dashboard panel. Do 

not block the sensor or let anything 

splash on it.

Summary of Contents for ATTO 3 2022










































































































































































































Reviews: