BYD ATTO 3 2022 Owner'S Manual Download Page 144

Page: 144 / 201

143

IN-CAR DEVICES

• In ventilation mode, the system

introduces the natural wind from

outside, which is suitable for spring and

autumn.

REMINDER

•A/C unpleasant smell:

It is normal that there may be a

damp and moldy smell just after

the A/C is turned on. That is due to

condensation that remains in the

evaporator and is not blown dry.

•How to prevent it:

Turn off the A/C and enable

natural ventilation before parking

to keep the air inside the vehicle

relatively dry.

Check, clean or replace the air

filter regularly.

Keep the cabin clean.

•If the unpleasant smell persists,

contact a BYD authorized dealer or

service provider for repair.

•It is normal that the A/C blower keeps

running after the vehicle is locked.

That is because the condensed water

on the surface of the evaporator

needs to be dried to prevent mold

fermentation.

Vents

Front Center Vent

• Move the knob to adjust airflow or to

open/close the vent.

• Toggle left/right to adjust airflow

direction.

Front Side Vents

• Move the knob to adjust airflow or to

open/close the vent.

• Toggle left/right to adjust airflow

direction.

Rear Side Vents

• Move the knob to adjust airflow or to

open/close the vent.

• Toggle left/right to adjust airflow

direction.

Summary of Contents for ATTO 3 2022










































































































































































































Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands

BYD ATTO 3 2022, Owner'S Manual

Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands