Bay Alarm Vista-20Bay Installation And Setup Manual Download Page 83

Page: 83 / 138

17–1

S E C T I O N 1 7

Zone Programming

(

✱

56/

✱

58 Menu Mode)

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

In This Section

♦

About Zone Programming

♦

✱

56 Zone Programming Procedures

♦

✱

58 Expert Programming Mode Procedures

♦

To Remove a Zone

♦

To Delete a Transmitter Serial Number

♦

To Enter and Duplicate Wireless Keys

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

About Zone Programming

✱

56 Zone Programming and

✱

58 Expert Programming are interactive menu modes that are

used to program zone numbers, alarm codes and report codes; and to identify the type of
input device. These modes can also be used for "enrolling" 5800 Series RF Wireless
Transmitter serial and loop numbers.

✱

56 Zone Programming can be used for entering alpha

descriptors for zones (we recommend entering descriptors in menu mode

✱

82). Refer to the

zone assignment table for

✱

56 and

✱

58 on the separate Programming Form.

✱

56 Zone Programming Procedures

NOTE:

Before proceeding, you must program field

✱

22 (RF System) and field

✱

25 (Wired

Zone Expansion) as required.

In the programming mode, press

✱

56.

SET

TO CONFIRM?

0 = NO 1 = YES

Confirm Transmitters:

The display at left appears upon entry

into

✱

56 mode. The default is

(No). If you enter

(Yes), you will

be prompted to confirm each transmitter after entering the serial
and loop numbers (at the

XMIT TO CONFIRM

prompt later in

this procedure).

We recommend that you confirm the programming of every
transmitter.

Enter Zn Num.

(00 = Quit)

Zone 10 entered

↑

Zone Number (Zn):

Enter the zone number that you wish to

program.

Zone 10 has been entered as an example in display at left.

Press [

✱

] to continue.

Zn ZT RC In: L

10 00 10 RF:

–

A summary

display

appears, showing the status of that zone’s

programming when using wireless keys.

NOTE:

If you are programming hard

wired

zones (01-06), the

following display appears:

Zn ZT RC In: RT

02 00 10 HW:

Refer to Response Time options on next page.

Press [

✱

] to continue.

Summary of Contents for Vista-20Bay











































































































































Search results

Summary of Contents for Vista-20Bay

Reviews:

Related manuals for Vista-20Bay

Brands by name

Popular brands

Bay Alarm Vista-20Bay, Installation And Setup Manual

Search results

Summary of Contents for Vista-20Bay

Reviews:

Related manuals for Vista-20Bay

Brands by name

Popular brands