Bay Alarm Vista-20Bay Installation And Setup Manual Download Page 125

Page: 125 / 138

Section 26 - Specifications & Accessories

26–3

4229 WIRED EXPANSION/RELAY MODULE

1. Physical:

6-1/2” W x 4-1/4” H x 1-1/4” D (169mm x 108mm x 32mm)

2. Electrical:

Voltage Input: 12VDC; Current Drain: 35mA (Relays off)

180mA (Relays on)

3. Interface Wiring:

To control panel's keypad connection points.

4. 8 EOLR Loops (A-H):

Loop A can be set for fast (10-15mSec) response to an open.

5. Two Output Relays:

SPDT Contacts, Rating: 2A max at 28VDC/AC

4285 VIP MODULE

1. Physical:

6-1/2” W x 4-1/4” H x 1-1/4” D (169mm x 108mm x 32mm)

2. Electrical:

Voltage Input: 12VDC; Current Drain: 160mA

3. DeviceAddress:

Permanently set to address 4.

4. Interface Wiring:

See

Section 8:

4285/4286 VIP Module

5. Telephone Line

Connections:

See

Section 8:

4285/4286 VIP Module

4286 VIP MODULE

1. Physical:

6-1/2” W x 4-1/4” H x 1-1/4” D (169mm x 108mm x 32mm)

2. Electrical:

Voltage Input: 12VDC, Current Drain: 300mA

3. DeviceAddress:

Permanently set to address 4.

4. Interface Wiring:

See

Section 8:

4285/4286 VIP Module

5. Telephone Line

Connections:

See

Section 8:

4285/4286 VIP Module

Accessories (Compatible Devices)

Transformers

No. 1321

16.5VAC, 25VA Plug-In Transformer

No. 4300

Powerline Carrier device Interface AC Transformer

Sounders

ADEMCO AB-12M

10” Motorized bell & box. UL Grade A. 100mA current draw.

ADEMCO 1011BE12M

10” Motorized bell & box. UL Listed. 100mA current draw.

ADEMCO 702

Self-contained 6-12 volt siren (driver built-in) and weatherproof

for outdoor use. Can be wired for either a steady or warble
sound.

ADEMCO 719

Two-channel, self-contained 6-12-volt siren (driver built-in).

109dB @ 10 feet. 550mA current draw.

ADEMCO 747

Self-contained 12-volt siren (driver built-in) for indoor wall

mount. 747F available for flush mounting.

ADEMCO 747UL

Self-contained siren (driver built-in) for indoor wall mount. UL

Listed.

ADEMCO 744

Siren driver with 6 jumper-selected sound outputs. Rated at

119dB with use of an 8-ohm 30-watt speaker.

ADEMCO 745X3

Voice siren driver with English, Spanish, and French voice

messages. Separate messages for fire and burglary. Use with 8-
ohm speaker. UL Listed.

ADEMCO 705820

15-watt, 8-ohm, 5” round speaker.

ADEMCO 713

40-watt, 8-ohm, indoor/outdoor speaker.

Summary of Contents for Vista-20Bay











































































































































Search results

Summary of Contents for Vista-20Bay

Reviews:

Related manuals for Vista-20Bay

Brands by name

Popular brands

Bay Alarm Vista-20Bay, Installation And Setup Manual

Search results

Summary of Contents for Vista-20Bay

Reviews:

Related manuals for Vista-20Bay

Brands by name

Popular brands