ScreenPRO-II Controller • User’s Guide
209
5. System Setup
Input Setup
táÇÉëÅêÉÉå=mÜ~ëÉ=~åÇ=`çäçê=_~ä~åÅÉ=pÉíìé
This section provides instructions for phase and color balance setup for wide widescreen
destinations utilizing BlendPRO-II. Please note the following important points:
•
For the optimum setup, it is
highly recommended
that you can output a test
pattern from each source — however, you can make adjustments using a live
image if necessary. For example, if the source is a PC, the best results can be
achieved when a full screen test pattern can be generated on the desktop.
•
A test pattern application is available on the website (
http://video.folsom.com
).
Click
Downloads
, select
BlendPRO
from the drop-down list, then download the
Alignment Patterns
application.
•
The following “phase adjustment” steps apply to
RGB
and
YUV
analog sources.
•
The following “color balance” steps apply to all types of analog sources —
RGB
,
YUV
,
Composite
and
S-Video
.
•
The following adjustment steps are
not required
for digital sources.
mÜ~ëÉ=^ÇàìëíãÉåíë
Use the following steps to set up phase for widescreen destinations — for
RGB
and
YUV
sources only.
1.
Ensure that you have performed the “standard” setups for your sources. If not,
refer to the “
Standard Input Setup
” section on page 206 for details.
2.
From the
Home Menu
, press
SYSTEM
to display the
System Menu
.
3.
Turn the
Modify Layers on Program
function to
On
.
4.
On the
Destination
Bus
, select your widescreen destination.
5.
On the ScreenPRO-II Controller console, select
LAYER A
.
6.
On the
Source Selection Bus
, select the
first
source that you want to set up.
7.
Press
PIP
to display the
PIP Adjustment Menu
.
8.
Ensure that the image’s border and shadow are turned off. Use the
Border Menu
and
Shadow Menu
as required.
9.
(
Recommended
) Output a
Burst
test pattern from the selected source.
10.
On the
PIP Adjustment Menu
, use
H Size
and
V Size
to size the PIP such that
that it matches the input’s resolution. In this way, there will be
no scaling
.
11.
Press
AUTO TRANS
to transition the PIP to program. This will ensure that you
can make your adjustments with data doubling and edge feathering visible.
12.
Using the
H Position
function, move the PIP into the screen 1 region.
13.
Press
HOME
>
INPUT
> {
SIZING
} to display the
Sizing Menu
for the source.
14.
On the
Destination
line, select the “screen 1” destination.
15.
Adjust
Clock Phase
for the cleanest and brightest image.
16.
If required, adjust
H Position
so that all of the image’s pixels are visible.
17.
Press
PIP
to display the
PIP Adjustment Menu
.
Note
These adjustments are primarily visual, rather than precisely
numerical. Here, for each destination, you are
visually
matching sources across your system’s scalers.
Summary of Contents for ScreenPRO-II
