Avaya IP500 Page 364 User Manual Download | Manualshive

Page: 364 / 402

background image

Deploying Avaya IP Office™ Platform IP500 V2

Page 364

15-601042 Issue 30j (18 May 2015)

IP Office™ Platform 9.1

Comments on this document? [email protected]

13.14.3 Trunk Licensing

The following trunks licenses can be used by a IP500 V2 system.

·

IP500 Universal PRI (Additional channels)
These licenses are used to enable additional B-channels above the basic 8 on an IP500 PRI-U card. The IP500 PRI-
U card supports E1, T1 and E1-R2 PRI modes. The IP Office system supports 8 unlicensed B-channels on each
IP500 PRI-U port fitted. Additional B-channels, up to the capacity of ports installed and PRI mode selected require
licenses. These additional channels consume licenses based on which additional channels are configured as in-
service from port 9 of slot 1 upwards. D-channels are not affected by licensing. The license is available in 2, 8 and
22 channel variants which can be combined for the total number of channels required.

·

SIP Trunk Channels
These licenses are used to configure the maximum number of simultaneous SIP trunk calls supported. The licenses
are consumed by calls in progress on a SIP channel. For SIP support the system also requires

VCM resources

.

The license is available in 1, 5, 10 and 20 channel variants which can be combined for the total number of
channels required.

·

IP500 Voice Networking
These licenses enable support for SCN, QSIG and H323 IP trunks. For voice networking support, the system also
requires

VCM resources

.

·

SM Trunk Channels
These licenses are used to enabled SM lines for connection to an Avaya Aura network. The IP Office system also
requires a Branch System license.

207

207

«
...
362
363
364
365
366
...
»

Summary of Contents for IP500



















































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: Yealink Pages: 8

Brand: T-Mobile Pages: 2

Brand: Panasonic Pages: 100

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 312

Brand: Panasonic Pages: 311

Brand: Fanvil Pages: 16

Brand: Sagem Pages: 72

Brand: Sagem Pages: 63

Brand: Sagem Pages: 77

Brand: UMX Pages: 12

Brand: TCL Pages: 25

Brand: Alcatel Pages: 4

Brand: Blu Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands