Avaya IP500 Page 90 User Manual Download | Manualshive

Page: 90 / 402

background image

Deploying Avaya IP Office™ Platform IP500 V2

Page 90

15-601042 Issue 30j (18 May 2015)

IP Office™ Platform 9.1

Comments on this document? [email protected]

7.7 Checking the LEDs

Control Unit LEDs

LED

Description

Optional SD

·

Off = Card shutdown.

·

Green on = Card present.

·

Green flashing = Card in use.

·

Orange steady = Reset imminent.

·

Red flashing = Card initializing or
shutting down.

·

Red fast flashing = card full

·

Red steady = Card failure/wrong type.

System SD

CPU

·

Alternate red/green = Starting up.

·

Green on = Okay.

·

Red on = No software.

·

Flashing Red = Error/Shutdown.

Base Card LEDs

Base Card

LEDs 1 to 8 Usage

All Cards

·

LED1 is also used for base card status:

·

Red On = Error

·

Red Slow Flash = Initializing.

·

Red Flash every 5 seconds = Card
okay.

·

Red Fast Flash = System shutdown.

IP500 Analog Phone

·

No status LEDs are used for analog phone extensions.

IP500 Digital Station

·

Green Flashing = Phone detected.

·

Green On = Phone active.

IP500 TCM8

·

Green On = Phone detected.

IP500 Combination

·

LEDs 1 to 6

·

Green Flashing = Phone detected.

·

Green On = Phone active.

IP500 VCM

·

LEDs 1 to 8 are unlabelled. They are used to indicate voice compression channel usage.
Each LED lit represents 12.5% of the available voice compression channel capacity in
use (total card capacity rather than licensed capacity).

IP500 4-Port Expansion

·

LEDs 1 to 8 are used for the expansion ports on the rear of the control unit. LEDs 9 to
12 are used for the card's own expansion ports.

Green

On

Expansion module present.

Red

Flashing

Initializing.

Red

On

Error.

Orange

Regular Flash

Base card okay.

Trunk Daughter Card LEDs

Trunk Daughter Card

LEDs 9 to 12 Usage

All cards

·

LED 9 is also used for daughter card status.

·

Red On = Error

·

Red Slow Flash = Initializing.

·

Red Flash every 5 seconds = Card okay.

·

Red Fast Flash = System shutdown.

Analog Trunk

·

Green on = V1: Card installed. V2: Line connected to the port but idle.

·

Green flashing = Line in use.

PRI Trunk

·

Off = No trunk present.

·

Green on = Trunk present.

·

Green flashing = Trunk in use.

·

Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) = Alarm indication
signal (AIS) from the trunk remote end.

·

Red with Green Blink (port 9) or Green Blink (port 10) = Port in loopback mode
(set through IP Office System Monitor).

BRI Trunk

·

Off = No trunk present.

·

Green on = Trunk present.

·

Green flashing = Trunk in use.

«
...
88
89
90
91
92
...
»

Summary of Contents for IP500



















































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: QMobile Pages: 13

Brand: ZEN Pages: 27

Brand: T-Mobile Pages: 4

Brand: T-Mobile Pages: 158

Brand: T-Mobile Pages: 212

Brand: Samsung Pages: 283

Brand: BENQ-SIEMENS Pages: 132

OpenStage SL4 professional HiPath Cordless...

Brand: Unify Pages: 80

Brand: Starmobile Pages: 53

Brand: NEC Pages: 61

Brand: T-Mobile Pages: 211

Brand: TCM Mobile Pages: 37

Brand: Brava Pages: 97

Brand: Pantech Pages: 61

Brand: Alcatel Pages: 2

my411Cv Vodafone

Brand: Sagem Pages: 96

Technophone PC200

Brand: Audiovox Pages: 12

Brand: Quba Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands