Avaya IP500 Page 79 User Manual Download | Manualshive

Page: 79 / 402

background image

Deploying Avaya IP Office™ Platform IP500 V2

Page 79

15-601042 Issue 30j (18 May 2015)

IP Office™ Platform 9.1

Comments on this document? [email protected]

Installing the Control Unit Cards:

6.1 Fitting IP500 Daughter Cards

IP500 trunk daughter cards can be fitted to any IP500 base card except the Unified Communications Module and 4-Port
Expansion card. For IP500 Combination cards, the trunk daughter card is pre-installed and cannot be changed.

Warnings

1. Correct anti-static protection steps should be taken while

handling circuit boards.

Parts and Equipment Required

1.

o

IP500 Base Card

2.

o

IP500 Trunk Daughter Card

3.

o

3 Stand Off Pillars

These are supplied with the trunk daughter card.

Tools Required.

1.

o

5mm Flat-blade screwdriver.

2.

o

Anti-static wrist strap and ground point.

Procedure: Installing a Trunk Daughter Card

1. Check that correct cards have been supplied.

2. Ensure that you are wearing an anti-static wrist strap connected

to a suitable ground point.

3. On the base card identify the position of 3 holes for the plastic

pillars for the IP500 card. These are along the same edge as the
card connector.

4. Fit the stand off pillars to the IP500 base card.

5. If there is a clip-on metal shield over the connector block on the

base card, remove it.

6. Using minimal force and checking that the pins are correctly

located, push the IP500 trunk card onto its connector block and
the stand off pillars.

7. Check that the card connector has snapped into position.

8. Using the washers and screws provided, secure the metal stand

off pillars to the base card.

9. A set of labels are supplied with the trunk daughter card. Fit the

appropriate label to the front of the base card.

«
...
77
78
79
80
81
...
»

Summary of Contents for IP500



















































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: Panasonic Pages: 10

Brand: Pantech Pages: 116

Brand: O2 Pages: 118

Brand: Xblue Networks Pages: 98

Brand: Polycom Pages: 2

Blackview GBV7100

Brand: Iget Pages: 62

Yealink SIP-T27

Brand: Vox Pages: 12

Brand: Verykool Pages: 30

Brand: Doro Pages: 5

Corded IP Phones

Brand: Swissvoice Pages: 12

Brand: TAG Heuer Pages: 62

Brand: Cosmocom Pages: 22

Curve 9320 Series

Brand: Blackberry Pages: 4

Brand: Binatone Pages: 104

Brand: Geemarc Pages: 47

Brand: Geemarc Pages: 72

Brand: Zte Pages: 2

Brand: XONTEL Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands