Avaya IP500 Page 213 User Manual Download | Manualshive

Page: 213 / 402

background image

Deploying Avaya IP Office™ Platform IP500 V2

Page 213

15-601042 Issue 30j (18 May 2015)

IP Office™ Platform 9.1

Comments on this document? [email protected]

System Components: IP500 Trunk Daughter Cards

13.3.3 PRI Trunk Cards

This card can be added to an IP500 base card to provide that card with support for PRI trunks. The card is available in
single port or dual port variants.

This card can be fitted to any IP500 base card except the IP500 4-Port Expansion card.

·

Ports/Channels
1 or 2

PRI trunk ports

. Each port supports the following PRI line types.

On dual port cards, both ports will be the same line type. The line type
selection can be changed using IP Office Manager. The options available
depend on the IP Office operation mode and locale.

·

E1 PRI (30B+D channels per port).

·

E1R2 PRI (30B channels per port).

·

T1 robbed bit (24B channels per port) or T1 PRI (23B+D channels
per port).

·

A T1(J) variant for use in Japan is also available (9.1 Feature
Pack and higher).

·

The required mode can be selected within IP Office Manager by right-
clicking on the line icon and selecting Change Universal PRI Card
Line Type and then selecting the required line type.

·

Physical trunk connection is via ports 9 and 10 of the host IP500 base
card.

·

Port 11 and 12 can be used as test points for connection of test and
monitoring equipment for the adjacent port.

·

Licenses
The IP Office system supports 8 unlicensed B-channels on each IP500 PRI-
U port fitted. Additional B-channels, up to the capacity of ports installed
and PRI mode selected require IP500 Universal PRI (Additional
Channels) licenses added to the configuration. These additional channels
consume the licenses based on which additional channels are configured as
in-service from port 9 of slot 1 upwards. D-channels are not affected by
licensing.

·

Maximum per Control Unit: 4 per control unit in IP Office standard
modes. 1 single port card only in other modes.

·

Software Level: 4.1+.

Daughter Card Ports (9-12)
The LEDs for ports 9 to 12 of the IP500 base card are used as follows:

·

Off = No trunk present.

·

Green on = Trunk present.

·

Green flashing = Trunk in use.

·

Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) = Alarm
indication signal (AIS) from the trunk remote end.

·

Red with Green Blink (port 9) or Green Blink (port 10) = Port in loopback
mode (set through IP Office System Monitor).

·

LED 9 is also used for daughter card status.

·

Red On = Error

·

Red Slow Flash = Initializing.

·

Red Flash every 5 seconds = Card
okay.

·

Red Fast Flash = System
shutdown.

Name

Description

SAP Code

IPO 500 TRNK PRI UNVRSL SNGL

IP Office 500 Trunk Card Primary Rate 1 Universal

700417439

IPO IP500 TRNK PRI UNVRSL SNGL TAA

"

Trade Agreements Act

compliant variant.

700501514

IPO 500 TRNK PRI UNIVRSL DUAL

IP Office 500 Trunk Card Primary Rate 2 Universal

700417462

IPO IP500 TRNK PRI UNVSL DUAL TAA

"

Trade Agreements Act

compliant variant.

700501517

IPO IP500 Trunk CARD T1(J) PRI DUAL
JAPAN

Dual T1(J) Interface Card

700509377

359

381

381

«
...
211
212
213
214
215
...
»

Summary of Contents for IP500



















































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: Pantech Pages: 101

Brand: Pantech Pages: 75

Yealink SIP-T46G

Brand: Yealink Pages: 6

Brand: Yealink Pages: 176

Brand: WM Systems Pages: 102

Brand: Ratel Pages: 2

Brand: Fysic Pages: 60

2100-TLL Landline 12v Tower

Brand: Rath Pages: 9

Brand: Polycom Pages: 2

Brand: Avaya Pages: 4

Brand: Alcatel Pages: 2

Brand: Sony Ericsson Pages: 40

Brand: Ericsson Pages: 77

Brand: LIKUID Pages: 33

Brand: Coolpad Pages: 41

Brand: Samsung Pages: 340

Brand: Samsung Pages: 218

Brand: Samsung Pages: 127

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands