Avaya IP500 User Manual Download Page 259

Page: 259 / 402

Deploying Avaya IP Office™ Platform IP500 V2

Page 259

15-601042 Issue 30j (18 May 2015)

IP Office™ Platform 9.1

Comments on this document? [email protected]

System Components: Phones

13.8.16 3645

The Avaya 3645 IP Wireless Telephone is a WiFi telephone that runs using H.323.

The availability of

VCM (Voice Compression Module)

channels is necessary to support IP telephony. For IP

Office 6.0+, these phones require an

Avaya IP Endpoints

license.

The 3645 supports the following features:

Lightweight innovative design .

Simple to use.

802.11a, 802.11b and 802.11g standard-compatible.

Transmission type Direct Sequence Spread Spectrum (DSSS).

FCC certification Part 15.247.

Management of telephones via DHCP and TFTP.

Voice encoding G711.

Wired Equivalent Privacy (WEP) - 40bit and 128 bit. WPA-PSK, WPA2-PSK.

5x16 character alphanumeric, plus status indicators.

4 hours talk time and 80 hours standby. Extendable with optional battery packs to 8 hours talk time and 160
hours standby.

Can be enabled for Push-to-talk (walkie-talkie) feature for broadcast between employees.

365

Summary of Contents for IP500



















































































































































































































































































































































































































Search results

Summary of Contents for IP500

Reviews:

Brands by name

Popular brands

Avaya IP500, User Manual

Search results

Summary of Contents for IP500

Reviews:

Brands by name

Popular brands