manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

Pinging the Linux system from the switch

Ping the Linux system from the switch by using Enterprise Device Manager to test connectivity.

Procedure steps

1. From the Device Manager menu bar, choose 

Device

, 

Open

.

OR

From the Device Manager toolbar, click 

Open Device

.

2. In the 

Device Name

 box, identify the device:

<ipv6 address>%interface num=number of ping messages

For example: 

f8a:0:0:0:0:0:203:1%eth0 num=1

Pinging the Avaya Ethernet Routing Switch 8800/8600 from
the Linux system

Ping the switch from the Linux system to test connectivity.

Procedure steps

Enter the following command on the Linux system to test communication with the

Avaya Ethernet Routing Switch 8800/8600:

# ping6 interface number

 

<8600 IPv6 address>%<interface number>

Example of pinging the switch from a Linux system

Procedure steps

Ping the switch:

# ping6 -I eth0 58a:0:0:0:0:0:204:1

Job aid: Sample ping output

Figure 21: Job aid: Ping from a LINUX system

 on page 348 shows sample output for pinging

the switch from a LINUX system.

Pinging the Linux system from the switch

Configuration — IPv6 Routing

November 2010     347

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

IBM 2210 Installation And Initial Configuration Manual preview
2210
Brand: IBM Pages: 72
D-Link DSL-2750U Setup preview
DSL-2750U
Brand: D-Link Pages: 14
D-Link DVG-7022S Quick Installation Manual preview
DVG-7022S
Brand: D-Link Pages: 7
D-Link DIR-878 Quick Installation Manual preview
DIR-878
Brand: D-Link Pages: 41
LaCie d2 Network 2 Quick Install Manual preview
d2 Network 2
Brand: LaCie Pages: 44
LaCie LaCie Ethernet Disk Datasheet preview
LaCie Ethernet Disk
Brand: LaCie Pages: 2
LaCie 5big - Network NAS Server Quick Start Manual preview
5big - Network NAS Server
Brand: LaCie Pages: 9
LaCie 2big NAS Quick Install Manual preview
2big NAS
Brand: LaCie Pages: 14
LaCie 12big Rack Fibre 8 Quick Install Manual preview
12big Rack Fibre 8
Brand: LaCie Pages: 9
National Instruments NI 9265 Operating Instructions Manual preview
NI 9265
Brand: National Instruments Pages: 26
National Instruments NI 9203 User Manual And Specifications preview
NI 9203
Brand: National Instruments Pages: 85
National Instruments Module SCXI-1503 User Manual preview
Module SCXI-1503
Brand: National Instruments Pages: 79
Parkside POF 1200 A1 Operation Manual preview
POF 1200 A1
Brand: Parkside Pages: 55
Parkside POF 1200 A1 Operation And Safety Notes preview
POF 1200 A1
Brand: Parkside Pages: 34
dixell XT120C Installing And Operating Insructions preview
XT120C
Brand: dixell Pages: 4
Macsense MIH-108 User Manual preview
MIH-108
Brand: Macsense Pages: 39
Xenya XS26GS User Manual preview
XS26GS
Brand: Xenya Pages: 189
B+B SmartWorx spectre lte User Manual preview
spectre lte
Brand: B+B SmartWorx Pages: 52

Brands by name

Popular brands

Load more brands