manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

Job aid

The following table shows the field descriptions for the 

show ip rsmlt info 

command.

Table 23: show ip rsmlt info command

Parameter

Description

VID

Indicates the VLAN ID.

IP

Indicates the IP address of the router.

MAC

Indicates the MAC address assigned.

ADMIN

Indicates the administrative status of RSMLT on the router.

OPER

Indicates the operational status of RSMLT on the router.

HDTMR

Indicates the hold-down timer value in the range of 0 to 3600 seconds.

HUTMR

Indicates the range of the hold-up timer in the range of 0 to 3600 seconds
or 9999. 9999 means infinity.

HDT REMAIN

Indicates the time remaining of the hold-down timer.

HUT REMAIN

Indicates the time remaining of the hold-up timer.

SMLT ID

Indicates the Split MultiLink Trunk ID.

SLT ID

Indicates the SLT ID.

Configuring RSMLT-edge

Configure RSMLT-edge to store the RSMLT peer MAC/IP address pair in its local configuration

file and restore the configuration if the peer does not restore after a simultaneous reboot of

both RSMLT peer switches. If enabled, all peer MAC/IP information for all RSMLT-enabled

VLANs saved during next the save configuration command.

Procedure steps

1. Enable or disable RSMLT-edge by using the following command: 

config ip

rsmlt rsmlt-edge-support <enable|disable>

2. Clear the peer MAC/IP information for the VLAN by using the following command:

config ip rsmlt clear-rsmlt-peer <vlanId>

3. Display RSMLT configuration and status information by using the following

command: 

config ip rsmlt info

IPv6 RSMLT configuration using the CLI

260     Configuration — IPv6 Routing

November 2010

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

NEC Univerge SV8100 System Configuration Manual preview
Univerge SV8100
Brand: NEC Pages: 44
Eaton INDGW-X2 Manual preview
INDGW-X2
Brand: Eaton Pages: 10
Patton electronics Patton SmartNode 2300 Series Specification Sheet preview
Patton SmartNode 2300 Series
Brand: Patton electronics Pages: 2
Paradyne 8540 Installation Instructions Manual preview
8540
Brand: Paradyne Pages: 12
Hornington AirStation WHR-G300N Settings preview
AirStation WHR-G300N
Brand: Hornington Pages: 6
Moxa Technologies PT-7324 Series User Manual preview
PT-7324 Series
Brand: Moxa Technologies Pages: 36
Cypress PSoC 4 S Series Quick Start Manual preview
PSoC 4 S Series
Brand: Cypress Pages: 4
AOpen ISDN SOHO Router User Manual preview
ISDN SOHO Router
Brand: AOpen Pages: 89
Unex EVK-351 Quick Start Manual preview
EVK-351
Brand: Unex Pages: 27
AirLive Ether-GSH24T v3 Quick Setup Manual preview
Ether-GSH24T v3
Brand: AirLive Pages: 2
ZyXEL Communications GS1100-10HP User Manual preview
GS1100-10HP
Brand: ZyXEL Communications Pages: 30
National Instruments PXI Terminal Block NI TB-2709 Installation Manual preview
PXI Terminal Block NI TB-2709
Brand: National Instruments Pages: 12
TP-Link Archer MR600 User Manual preview
Archer MR600
Brand: TP-Link Pages: 113
VIA Technologies Mobile360 M810 Quick Start Manual preview
Mobile360 M810
Brand: VIA Technologies Pages: 25
Patton ipRocketLink 3101 Series Getting Started Manual preview
ipRocketLink 3101 Series
Brand: Patton Pages: 119
Aztech na8300 Easy Start preview
na8300
Brand: Aztech Pages: 13
Divio NRM 311 User Manual preview
NRM 311
Brand: Divio Pages: 78
Cambium Networks PTP 850E Installation Manual preview
PTP 850E
Brand: Cambium Networks Pages: 99

Brands by name

Popular brands

Load more brands