manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

Procedure steps

Enable the multicast router by using the following command:

config ipv6 mcast <enable|disable>

Enabling a VLAN for multicast routing

Configure a VLAN for multicast traffic to enable MLD on the VLAN.

Procedure steps

Enable a VLAN for multicast routing by using the following command:

config vlan

 

<vid>

 

ipv6 mcast <enable|disable>

Variable definitions

Use the data in the following table to use the 

config vlan ipv6 mcast <enable|

disable>

 command.

Variable

Value

<vid>

Specifies a VLAN ID in the range of 1–4094.

Configuring MLD on a VLAN

Configure MLD on a VLAN to customize the configuration.

Procedure steps

Configure MLD by using the following command:

Multicast protocol configuration using the CLI

296     Configuration — IPv6 Routing

November 2010

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
N-Tron 7018 User Manual & Installation Manual preview
7018
Brand: N-Tron Pages: 138
Yamaha mLAN Driver Manual Book preview
mLAN Driver
Brand: Yamaha Pages: 24
Yamaha DSP1D Supplementary Manual preview
DSP1D
Brand: Yamaha Pages: 5
Planet ADSL 2/2+ Router with USB Port ADE-3410v2 User Manual preview
ADSL 2/2+ Router with USB Port ADE-3410v2
Brand: Planet Pages: 62
Brocade Communications Systems NetIron MLXe Series Hardware Installation Manual preview
NetIron MLXe Series
Brand: Brocade Communications Systems Pages: 305
National Instruments FieldPoint FP-3000 User Manual preview
FieldPoint FP-3000
Brand: National Instruments Pages: 118
Teletronics International TT 900 User Manual preview
TT 900
Brand: Teletronics International Pages: 57
Microtek MiniLink Operation Manual preview
MiniLink
Brand: Microtek Pages: 25
Zhone ETHX-2214-DS3 Installation Instructions Manual preview
ETHX-2214-DS3
Brand: Zhone Pages: 28
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Brand: Stahl Pages: 2
EMC VNX5300 Block Hardware Information Manual preview
VNX5300 Block
Brand: EMC Pages: 88
ZyXEL Communications Prestige 643 User Manual preview
Prestige 643
Brand: ZyXEL Communications Pages: 191
Lindy Modular Fast Fiber Switch Converter MT-RJ Specifications preview
Modular Fast Fiber Switch Converter MT-RJ
Brand: Lindy Pages: 3
Edgewater Networks EdgeMarc 4300T Installation Manual preview
EdgeMarc 4300T
Brand: Edgewater Networks Pages: 23
Stephen SON8010U User Manual preview
SON8010U
Brand: Stephen Pages: 8
Alcatel-Lucent Broadband 700 MHz Brochure preview
Broadband 700 MHz
Brand: Alcatel-Lucent Pages: 8
Avaya X330W-2USP Quick Start Manual preview
X330W-2USP
Brand: Avaya Pages: 16

Brands by name

Popular brands

Load more brands