Avaya ERS 8600 series Configuration Manual Download

Page: 97 / 420

Command

Parameter

admin

mcast

mtu

reachable-time

retransmit-time

config vlan <vlan id> ipv6 nd

dad-ns

default

hop-limit

info

life-time

managed-flag

other-stateful

route-advertisement

rtr-advert

Assigning an IPv6 address to the management port

The Avaya Ethernet Routing Switch 8800/8600 switch contains an Ethernet port in the SF/

CPU slot. You can assign IPv6 addresses to this port to manage the device.

Perform duplicate address detection (DAD) for the management IPv6 address.

Important:

Do not advertise the management route to the regular routing domain (OSPFv3) or advertise

the prefix information for the management interface in router advertisement.

Procedure steps

Assign an IPv6 address to the management port:

Assigning an IPv6 address to the management port

Configuration — IPv6 Routing

November 2010 97

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Search results

Summary of Contents for ERS 8600 series

Reviews:

Related manuals for ERS 8600 series

Brands by name

Popular brands

Avaya ERS 8600 series, Configuration Manual

Search results

Summary of Contents for ERS 8600 series

Reviews:

Related manuals for ERS 8600 series

Brands by name

Popular brands