Avaya ERS 8600 series Configuration Manual Download

Page: 181 / 420

Configuring OSPF global parameters

Configure Open Shortest Path First (OSPF) global parameters to affect OSPF routing on the

entire switch. Routers use the OSPF protocol to exchange network topology information,

providing each router with a map of the network.

Prerequisites

You must log on to the Global Configuration mode in the ACLI.

Procedure steps

1. Enable OSPF for IPv6 by using the following command:

router ospf ipv6-enable

2. Log on to the OSPF Router configuration mode by using the following command:

router ospf

3. Enable the OSPF autonomous system boundary router by using the following

command:

ipv6 as-boundary-router enable

4. Configure the OSPF router ID by using the following command:

ipv6 router-id <A.B.C.D>

Variable definitions

Use the data in the following table to use the

ipv6 router-id

command.

Variable

Value

router-id

<A.B.C.D>

Configures the OSPF router ID IPv6 address.

Configuring OSPF global parameters

Configuration — IPv6 Routing

November 2010 181

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Search results

Summary of Contents for ERS 8600 series

Reviews:

Related manuals for ERS 8600 series

Brands by name

Popular brands

Avaya ERS 8600 series, Configuration Manual

Search results

Summary of Contents for ERS 8600 series

Reviews:

Related manuals for ERS 8600 series

Brands by name

Popular brands