manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

config vlan 40 ipv6 admin enable

Configuring an IPv4 VLAN on the destination device

Configure an IPv4 VLAN (VLAN 30 in the figure) on the destination device (8600 2 in the figure).
The IPv4 VLAN encapsulates the IPv6 VLAN across the IPv4 network.

Procedure steps

1. Create the VLAN by using the following command:

config vlan 30 create byport 1

2. Add ports to the VLAN by using the following command:

config vlan 30 ports add 3/30

3. Assign an IPv4 address to the VLAN by using the following command:

config vlan 30 ip create 192.168.20.1/24

4. Enable OSPF on the VLAN by using the following command:

config vlan 30 ip ospf enable

5. Enable OSPF on the device by using the following command:

config ip ospf enable

Configuring the tunnel on the source device

Procedure steps

Enter the following command to configure the tunnel on the source device. Enter the

IPv4 address for the destination device (8600 2) for the remote-address value.

config ipv6 tunnel 1 create local-addr 172.21.80.1 ipv6addr

2500::1/120 remote-address 192.168.20.1

Configuring the tunnel on the destination device

Procedure steps

Enter the following command to configure the tunnel on the destination device. Enter

the IPv4 address for the source device (8600 1) for the remote-address value.

config ipv6 tunnel 1 create local-addr 192.168.20.1 ipv6addr

2500::2/120 remote-address 172.21.80.1

IPv6 CLI configuration

378     Configuration — IPv6 Routing

November 2010

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

Patton electronics 4520 Specification Sheet preview
4520
Brand: Patton electronics Pages: 2
Patton electronics 4520 Getting Started Manual preview
4520
Brand: Patton electronics Pages: 86
TVT Digital TD-3316B4-16P-A1 Quick Start Manual preview
TD-3316B4-16P-A1
Brand: TVT Digital Pages: 2
Eaton SONiX Pm10 Technical Manual preview
SONiX Pm10
Brand: Eaton Pages: 14
Patton electronics ipRocketLink 3086FR Quick Start Manual preview
ipRocketLink 3086FR
Brand: Patton electronics Pages: 12
i-MO OptiBond 210 C Series Hardware Installation Manual preview
OptiBond 210 C Series
Brand: i-MO Pages: 16
Vaisala TERMBOX-9000 User Manual preview
TERMBOX-9000
Brand: Vaisala Pages: 32
Proxim TeraBridge 5845 Specifications preview
TeraBridge 5845
Brand: Proxim Pages: 4
WTI NPS-16HD20-1 User Manual preview
NPS-16HD20-1
Brand: WTI Pages: 178
Helmholz 700-160-3EN02 Quick Start Manual preview
700-160-3EN02
Brand: Helmholz Pages: 14
Telit Wireless Solutions WE866C3 User Manual preview
WE866C3
Brand: Telit Wireless Solutions Pages: 37
ZyXEL Communications Dimension GS-2024 User Manual preview
Dimension GS-2024
Brand: ZyXEL Communications Pages: 266
Paradyne Hotwire 7996 User Manual preview
Hotwire 7996
Brand: Paradyne Pages: 46
IBM Turbo 16/4 Token-Ring PC Card 2 User Manual preview
Turbo 16/4 Token-Ring PC Card 2
Brand: IBM Pages: 123
Billion BiPAC 7560G Specifications preview
BiPAC 7560G
Brand: Billion Pages: 2
Westermo SDW-500 User Manual preview
SDW-500
Brand: Westermo Pages: 22
LG N4B2N Specifications preview
N4B2N
Brand: LG Pages: 2
LG V-net ACS PWFMDB000 Installation & User Manual preview
V-net ACS PWFMDB000
Brand: LG Pages: 48

Brands by name

Popular brands

Load more brands