manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

Figure 23: Dual stack system

Use the following example to configure OSPF.

Procedure steps

1. Create an IPv4 interface.

Enter the following command for a VLAN:

config vlan 100 ip create 1.1.1.1/24 100

Enter the following command for a brouter port:

config ethernet 2/1 ip create 1.1.1.1/24 100

2. Configure an OSPF area for the interface.

Enter the following command for a VLAN:

config vlan 100 ip ospf area 1.1.1.1

Enter the following command for a brouter port:

config ethernet 2/1 ip ospf area 1.1.1.1

3. Enable OSPF on the interface.

Enter the following command for a VLAN:

Routing both IPv4 and IPv6 traffic

Configuration — IPv6 Routing

November 2010     371

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

Habitat M10 Installation Manual preview
M10
Brand: Habitat Pages: 48
Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Brand: Lantronix Pages: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Brand: Lantronix Pages: 7
Lantronix Maestro E220 Series Quick Start Manual preview
Maestro E220 Series
Brand: Lantronix Pages: 25
PaloAlto Networks PA-7500 Quick Start Manual preview
PA-7500
Brand: PaloAlto Networks Pages: 3
AlphaShield INTERNET PRIVACY PROTECTION (Spanish) Manual Del Usuario preview
INTERNET PRIVACY PROTECTION
Brand: AlphaShield Pages: 49
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Watchguard XTM 850 Hardware Manual preview
XTM 850
Brand: Watchguard Pages: 30
DIGIWEB Box 7360 Quick Setup Manual preview
Box 7360
Brand: DIGIWEB Pages: 16
NetComm 4GM3W User Manual preview
4GM3W
Brand: NetComm Pages: 65
rtd IDAN-ID5915 User Manual preview
IDAN-ID5915
Brand: rtd Pages: 28
Extreme Networks ACC-BKT-AX-BEAM Accessories Manual preview
ACC-BKT-AX-BEAM
Brand: Extreme Networks Pages: 35
IEI Technology PUZZLE-IN005 User Manual preview
PUZZLE-IN005
Brand: IEI Technology Pages: 106
Aztech na8300 Easy Start preview
na8300
Brand: Aztech Pages: 13
Extreme Networks ExtremeCloud Appliance E3120 Installation Manual preview
ExtremeCloud Appliance E3120
Brand: Extreme Networks Pages: 27
PACOM PPRO-UR-4EDX Quick Manual preview
PPRO-UR-4EDX
Brand: PACOM Pages: 16
Billion BiPAC 645 Quick Start Manual preview
BiPAC 645
Brand: Billion Pages: 16
BinTec BIANCA/BRICK XS Quick Install Manual preview
BIANCA/BRICK XS
Brand: BinTec Pages: 2

Brands by name

Popular brands

Load more brands