manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

Variable

Value

FlowLabel

Displays the method used to set the IPv6 Flow Label value. This
object need not be present in rows where tunnelIfAddressType
indicates the tunnel is not over IPv6. A value of -1 indicates that
a traffic conditioner is invoked and more information can be
available in a traffic conditioner MIB. Any other value indicates
that the Flow Label field is configured to the indicated value.

AddressType

Displays Manual for a manually configured tunnel, or sixToFour
for autoconfigured tunnels.

LocalInetAddress

Identifies the local endpoint address of the tunnel.

RemoteInetAddress

Identifies the remote endpoint of the tunnel.

EncapsLimit

Displays the address of the local endpoint of the tunnel (that is,
the source address used in the outer IP header). If the address
is unknown, the value is 0.0.0.0 for IPv4 or :: for IPv6. The
tunnelIfAddressType displays the object type.

IPv4-to-IPv6 transition mechanism configuration using Enterprise Device Manager

274     Configuration — IPv6 Routing

November 2010

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
D-Link Verizon DSL-2750B Connection Instructions preview
Verizon DSL-2750B
Brand: D-Link Pages: 2
D-Link DVA-2800 Quick Start Manual preview
DVA-2800
Brand: D-Link Pages: 4
Tripp Lite N48M Series Installation Manual preview
N48M Series
Brand: Tripp Lite Pages: 20
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Brand: Tandberg Data Pages: 6
Xircom RealPort Ethernet 10/100 User Manual preview
RealPort Ethernet 10/100
Brand: Xircom Pages: 30
Tektronix CTS 850 User Manual preview
CTS 850
Brand: Tektronix Pages: 178
Zonet ZSR4134WS User Manual preview
ZSR4134WS
Brand: Zonet Pages: 53
X-Micro IEEE 802.11b User Manual preview
IEEE 802.11b
Brand: X-Micro Pages: 49
Airlink101 AR325W Quick Installation Manual preview
AR325W
Brand: Airlink101 Pages: 13
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Brand: Divio Pages: 4
3Com 3C433279A Release Note preview
3C433279A
Brand: 3Com Pages: 12
ADC HiGain H4TU-R-402 List 5A Quick Installation preview
HiGain H4TU-R-402 List 5A
Brand: ADC Pages: 7
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2
Netopia D3100-I User Reference Manual preview
D3100-I
Brand: Netopia Pages: 138
Aaeon FWS-7811 Manual preview
FWS-7811
Brand: Aaeon Pages: 100
B&B Electronics Elinx EIRP410-2SFP-T Manual preview
Elinx EIRP410-2SFP-T
Brand: B&B Electronics Pages: 24
Paradyne FrameSaver DSL 9783 CSU/DSU User Manual preview
FrameSaver DSL 9783 CSU/DSU
Brand: Paradyne Pages: 233

Brands by name

Popular brands

Load more brands