AudioCodes Mediant 2000, User Manual

Page: 154 / 418

SIP User's Manual 154 Document #: LTRT-68808
Mediant 2000
Parameter Description
If the called number in IP-to-Tel call includes the characters 'w' or 'p',
the device places a call with the first part of the called number (before
'w' or 'p') , and plays DTMF digits after the call is answered. If the
character 'w' is used, the device waits for detection of dial tone before it
starts playing DTMF digits. For example, if the called number is
'1007766p100', the device places a call with 1007766 as the destination
number, then after the call is answered, it waits 1.5 seconds ('p') and
plays the rest of the number (100) as DTMF digits.
Additional examples: 1664wpp102, 66644ppp503, and
7774w100pp200.
RTP Only Mode
[RTPOnlyMode]
Enables the device to start sending and/or receiving RTP packets to
and from remote endpoints without the need to establish a Control
session. The remote IP address is determined according to the 'Tel to
IP Routing' table (refer to ''Tel to IP Routing Table'' on page
175 ) or
'Outbound IP Routing' table (refer to “Outbound IP Routing Table” on
page
178 ). The port is the same port as the local RTP port (set by
BaseUDPPort and the channel on which the call is received).
ƒ
[0]
Disable = Disable (default).
ƒ
[1]
Transmit & Receive = Send and receive RTP.
ƒ
[2]
Transmit Only= Send RTP only.
ƒ
[3]
Receive Only= Receive RTP only.
Notes:
ƒ
To configure the RTP Only mode per trunk, use the
RTPOnlyModeForTrunk_ID (refer to “Configuring the Trunk Settings”
on page
82 ).
ƒ
If per trunk configuration (using RTPOnlyModeForTrunk) is set to
other than default, the RTPOnlyMode parameter value is overridden.
PSTN Alert Timeout
[PSTNAlertTimeout]
Alert Timeout (in seconds) (ISDN T301 timer) for calls to PSTN. This
timer is used between the time a SETUP message is sent to the Tel
side (IP-to-Tel call establishment) and a CONNECT message is
received. If an ALERTING message is received, the timer is restarted.
The default is 180 seconds. The range is 1 to 600.
Note:
If per trunk configuration (using TrunkPSTNAlertTimeout) is set to
other than default (refer to “Configuring the Trunk Settings” on page 82 ),
the PSTNAlertTimeout parameter value is overridden.
Reanswer Time
[RegretTime]
Determines the time period the device waits for an MFC R2 Resume
(Reanswer) signal once a Suspend (Clear back) signal is received from
the PBX. If this timer expires, the call is released.
Note:
Applicable only for MFC R2 CAS Brazil variant.
The valid range is 0 to 255 (in seconds). The default value is 0.
Disconnect and Answer Supervision
Send Digit Pattern on
Connect
[TelConnectCode]
Defines a digit pattern to send to the Tel side after SIP 200 OK is
received from the IP side. The digit pattern is a pre-defined DTMF
sequence that is used to indicate an answer signal (e.g., for billing).
The valid range is 1 to 8 characters.
Note:
This parameter is applicable to FXO and CAS.
Disconnect on Broken
Connection
[DisconnectOnBrokenCo
Determines whether the device releases the call if RTP packets are not
received within a user-defined timeout.
ƒ
[0]
No