manualshive.com logo in svg

ARTERY AT32F413 Series, Reference Manual, Page: 354 / 369

Share
Download
ARTERY AT32F413 Series Reference Manual Download Page 354

  AT32F413

 

Series  Reference  Manual

 

2022.06.27

 

Page 354 

 

Rev 2.00

 

SDIO interrupts 

There is a pin with interrupt feature on the SD interface in oder to enable the SD I/O card to interrupt the 
MultiMedia card/SD module. In 4-bit SD mode, this pin is SDIO_D1. The SD I/O interrupts are detected 
when  the  level  is  active.  In  other  words,  the  interrupt  signal  line  must  be  active  (low)  before  it  is 
recognized and responded by the MultiMedia card/SD module, and will remain inactive (high) at the end 
of the interrupt routine. 
When the SDIO_DTCTRL [11] bit is set, the SDIO interrupts are detected on the SDIO_D1 signal line. 

23.4 SDIO registers 

The device communicates with the system through 32-bit control registers accessible via AHB. 
The peripheral registers must be accessed by words (32-bit). 

Table 23-24

 

A summary of the

 SDIO registers.

 

Register 

Offset 

Reset value 

SDIO_PWRCTRL 

0x00 

0x0000 0000 

SDIO_CLKCTRL 

0x04 

0x0000 0000 

SDIO_ARG 

0x08 

0x0000 0000 

SDIO_CMD 

0x0C 

0x0000 0000 

SDIO_RSPCMD 

0x10 

0x0000 0000 

SDIO_RSP1 

0x14 

0x0000 0000 

SDIO_RSP2 

0x18 

0x0000 0000 

SDIO_RSP3 

0x1C 

0x0000 0000 

SDIO_RSP4 

0x20 

0x0000 0000 

SDIO_DTTMR 

0x24 

0x0000 0000 

SDIO_DTLEN 

0x28 

0x0000 0000 

SDIO_DTCTRL 

0x2C 

0x0000 0000 

SDIO_DTCNTR 

0x30 

0x0000 0000 

SDIO_STS 

0x34 

0x0000 0000 

SDIO_INTCLR 

0x38 

0x0000 0000 

SDIO_INTEN 

0x3C 

0x0000 0000 

SDIO_BUFCNTR 

0x48 

0x0000 0000 

SDIO_BUF 

0x80 

0x0000 0000 

23.4.1  SDIO power control register (SDIO_ PWRCTRL) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 2 

Reserved 

0x0000 0000  resd 

Kept at its default value. 

Bit 1: 0 

PS 

0x0 

rw 

Power switch 
These bits are set or cleared by software. They are used 
to define the current status of the card clock. 
00: Power-off, the card clock is stopped. 
01: Reserved 
10: Reserved 
11: Power-on, the card clock is started. 

Note:  Write  access  to  this  reg ister  is  not  allowed  within  seven  HCLK  clock  periods  after 
data is written. 

Summary of Contents for AT32F413 Series


















































































































































































































































































































































































Reviews:

No comments