manualshive.com logo in svg

ARTERY AT32F413 Series, Reference Manual, Page: 138 / 369

Share
Download
ARTERY AT32F413 Series Reference Manual Download Page 138

  AT32F413

 

Series  Reference  Manual

 

2022.06.27

 

Page 138 

 

Rev 2.00

 

1: Underload 
In reception mode: 
0: Normal 
1: Overload 
This  bit  is  cleared  by  software,  or  by  hardware  when 
I2CEN=0.   

Bit 10 

ACKFAIL 

0x0 

rw0c 

Acknowledge failure flag 
0: No acknowledge failure 
1: Acknowledge failure occurs. 
Set by hardware when no acknowledge is returned. 
This  bit  is  cleared  by  software,  or  by  hardware  when 
I2CEN=0. 

Bit 9 

ARLOST 

0x0 

rw0c 

Arbitration lost flag 
0: No arbitration lost is detected. 
1: Arbitration lost is detected. 
This  bit  is  cleared  by  software,  or  by  hardware  when 
I2CEN=0. 
On  ARLOST  even,  the  I

2

C  interface  switches  to  slave 

mode automatically. 

Bit 8 

BUSERR 

0x0 

rw0c 

Bus error flag 
0: No Bus error occurs. 
1: Bus error occurs. 
Set by hardware when the interface detects a misplaced 
Start or Stop condition. 
This  bit  is  cleared  by  software,  or  by  hardware  when 
I2CEN=0. 

Bit 7 

TDBE 

0x0 

ro 

Transmit data buffer empty flag 
0: The data is being transferred from the DT register to the 
shift register (the data is still loaded with the data at this 
point.) 
1: The data has been moved from the DT register to the 
shift register. The data register is empty now.   
This flag is set when the DT register is empty, and cleared 
when writing to the DT register. 
Note: The TDBE bit is not cleared by writing the first data 
to be transmitted, or by writing data when the TDC is set, 
since the data register is still empty at this time. 

Bit 6 

RDBF 

0x0 

ro 

Receive data buffer full flag 
0: Data register is empty. 
1: Data register is full (data received) 
This flag is cleared when the DT register is read. 
The RDBF bit is not set at ARLOST event. 

Bit 5 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 4 

STOPF 

0x0 

ro 

Stop condition generation complete flag 
0: No Stop condition is detected. 
1: Stop condition is detected. 
This  bit  is  set  by  hardware  when  a  Stop  condition  is 
detected on the bus by the slave if ACKEN=1. 
It is cleared by reading STS1 register followed by writing 
to the CTRL1 register. 

Bit 3 

ADDRHF 

0x0 

ro 

Master 9~8 bit address head match flag 
0: Master 9~8 bit address head mismatch 
1: Master 9~8 bit address head match 
Set by hardware when the first byte is sent by master in 
10-bit address mode. 
Cleared by a write to the CTRL1 register after the STS1 

Summary of Contents for AT32F413 Series


















































































































































































































































































































































































Reviews:

No comments