manualshive.com logo in svg

ARTERY AT32F413 Series, Reference Manual, Page: 313 / 369

Share
Download
ARTERY AT32F413 Series Reference Manual Download Page 313

  AT32F413

 

Series  Reference  Manual

 

2022.06.27

 

Page 313 

 

Rev 2.00

 

20.7.1.7 

CAN error status register (CAN_ESTS) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 24  REC 

0x00 

ro 

Receive error counter 
This  counter  is  implemented  in  accordance  with  the 
receive  part  of  the  falut  confinement  mechanism  of  the 
CAN protocol. 

Bit 23: 16  TEC 

0x00 

ro 

Transmit error counter 
This  counter  is  implemented  in  accordance  with  the 
transmit  part  of  the  falut  confinement  mechanism  of  the 
CAN protocol. 

Bit 15: 7 

Reserved 

0x00 

resd 

Kept at its default value. 

Bit 6: 4 

ETR 

0x0 

rw 

Error type record 
000: No error 
001: Bit stuffing error 
010: Format error   
011: Acknowledgement error 
100: Recessive bit error 
101: Dominant bit error 
110: CRC error 
111: Set by software 
Note: 
This field is used to indicate the current error type. It is set 
by hardware according to the error condition detected on 
the CAN bus. It is cleared by hardware when a message 
has been transmitted or received successfully. 
If the error code 7 is not used by hardware, this field can 
be set by software to monitor the code update. 

Bit 3 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 2 

BOF 

0x0 

ro 

Bus-off flag 
0: Bus-off state is not entered. 
1: Bus-off state is entered. 
Note: When the TEC is greater than 255, the bus-off state 
is entered, and this bit is set by hardware. 

Bit 1 

EPF 

0x0 

ro 

Error passive flag 
0: Error passive state is not entered 
1: Error passive state is entered 
Note: This bit  is set  by  hardware  when  the current  error 
times has reached the Error passive state limit (Receive 
Error Counter or Transmit Error Counter >127) 

Bit 0 

EAF 

0x0 

ro 

Error active flag 
0: Error active state is not entered 
1: Error active state is entered 
Note: This bit  is set  by  hardware  when  the current  error 
times  has  reached  the  Error  active  state  limit  (Receive 
Error Counter or Transmit Error Counter ≥96) 

Summary of Contents for AT32F413 Series


















































































































































































































































































































































































Reviews:

No comments