Arkray SPOTCHEM EZ SP-4430 Page 48 Operating Manual Download

Page: 48 / 139

2-22 ● SP-4430

1-4

装置の設置

Chapter 2 MEASUREMENT

2-3-4

検体の準備

Set the samples.

Open the protective cover and place

the uncapped centrifuge tube in

position.

Close the cover.

●

■

Measurement of uncentrifuged whole blood.

NOTE

Make sure the sample tubes are

uncapped, otherwise it may

cause breakage of centrifuge

tube and the Nozzle.

Set a sample after removing the

cap.

Uncap sample tubes and place them

to the port of the multi-rack.

●

■

Measurement of serum or plasma, or centrifuged samples.

NOTE

Make sure the sample tubes are

uncapped, otherwise it may

cause breakage of the Nozzle.

NOTE

Make sure the protective cover is

closed properly.

If the protective cover remains

open, it may become troubled

and correct measurement results

may not be obtained.

NOTE

Make sure the protective cover is

closed properly.

If the protective cover remains

open, it may cause a trouble.

Summary of Contents for SPOTCHEM EZ SP-4430












































































































































Search results

Summary of Contents for SPOTCHEM EZ SP-4430

Reviews:

Related manuals for SPOTCHEM EZ SP-4430

Brands by name

Popular brands

Arkray SPOTCHEM EZ SP-4430, Operating Manual

Search results

Summary of Contents for SPOTCHEM EZ SP-4430

Reviews:

Related manuals for SPOTCHEM EZ SP-4430

Brands by name

Popular brands